FREE Lifetime Tech Support
We're here to help you Do The Job Right.
This product includes FREE Lifetime Tech Support from our U.S.-Based Customer Solutions Team.
Looking for advice on your project or product recommendations? Our in-house Project Advisors have the same passion for DIY automotive restoration as you do. Get advice on your project, personalized product recommendations and answers to your questions. Give us a call or email projectadvisors@eastwood.com.
Rated 5 out of
5 by
Dave from
Eastwood tubing bender and diesThe new die set should work as well as the previous sets. The machining is good and the die parts fit the bender as designed.
Date published: 2024-10-03
Rated 5 out of
5 by
RyDaddy from
Whole roll cage built with minimal issuesI did have an issue with a bend pin, but Eastwood remedied that quickly.
Date published: 2023-03-05
Rated 5 out of
5 by
RyDaddy from
Nice UnitI need to fight the pin out of the saddle to get the bent tube out, but I figured out a technique to make it work. Probably just that I am using it at its limit on 2" x .120-wall tube.
Date published: 2023-03-05
Rated 5 out of
5 by
Anonymous from
Fits the Woodward WFB2Bought this to find out if the Woodward Fab and Eastwood tube bending dies were interchangeable. The answer is yes. These dies fit the Woodward Fab WFB2 bender.
Read the other reviews and I can tell you the one where the holding clamp got bent was operator error. If you use the shortest pin it doesn't seat far enough and the bottom will slip off. So make sure you use the correct pin.
Date published: 2020-02-20
Rated 5 out of
5 by
Anonymous from
It Fits WFB2Bought this die to figure out once and for all if the Woodward Fab and Eastwood tubing dies were interchangeable. The answer is YES THESE DIES WILL FIT THE WFB2 tubing bender as well.
Date published: 2020-02-20
Rated 5 out of
5 by
Tony from
advice for soft tubingReading through the reviews I see many questions about bending aluminum and kinking issues. The trick to bending soft materials with any bender is to cap one end of the tube, fill it with sand, then cap the final end. The sand will go around the bend and support the tube from the inside.
"Eastwood 21122, Can this be used with Eastwood 21115 to bend chrome molly 2” pipe?"
Yes, the Eastwood 21115 High-Capacity Tubing Bender can bend chrome-moly tubing up to 2 inches in diameter when used with the appropriate die sets. However, it is important to note that the bending capacity depends on the wall thickness of the tubing. Ensure you are using the correct die set for the specific size and material of the tubing to achieve accurate and smooth bends.
Answered by: Greg A Tech Advisor
Date published: 2025-02-06
What is the lightest gauge you can bend at 90 degreesWith the 2” die set
Asked by: Raymo
Thanks for you question.
The Eastwood High Capacity Tubing Bender is capable of bending tubing from 1 Inch to 2 Inch OD and Form bends in up to 0.120” wall tubing. Too thin walled and it could kink the bend.
.
Answered by: Wil Tech Support
Date published: 2025-01-27
How would you remove the material after you bent it to 240°?
Asked by: Twisted trail tech
you can tap the tubing off the tool by using a rubber or wooden mallet.
Answered by: Anonymous
Date published: 2023-05-06
Does the 120 degree die work differently than the 240 and how? Tnx
Asked by: 396mafia
The die does not operate any differently, but you will be limited to 120° or 240° maximum bends. If you need more than 120° of angle definitely go with a 240° die.
Answered by: Nick BC
Date published: 2022-05-26
Do you have a 1 1/4, die for tubing bender?
Asked by: Steve
We do not have a 1.25" die for this bender at this moment
Answered by: ZachC
Date published: 2022-05-12
I can bend pipe 1-1/4 sch40. Normally what I work are railings.
Asked by: Ricardo
We do not offer a 1 1/4" die at the moment
Answered by: ZachC
Date published: 2024-02-09
Will this bender work to bend EMT conduit if you use the correct die? I need to bend 1.25" EMT conduit, the OD is 1.50 and the wall thickness is .072
Asked by: Walter
We do not recommend using this tool to bend EMT conduit.
Answered by: ZachC
Date published: 2024-02-09
Can the bender bend 1 1/4 dom tube
Asked by: Qelder92
We do not currently have a 1 1/4" die for this machine at this time.
Chat 
