Eastwood Extreme Chassis Black Primer
For a more durable Extreme Chassis Black® finish on bare metal, start with this Extreme Chassis Black® Primer.
Once your chassis is stripped of old paint and surface rust, apply Eastwood Extreme Chassis Black® Primer as the foundation for a lasting finish. This black metal primer is specifically formulated for use with Eastwood Original Chassis Black Paint and Extreme Chassis Black. We’ve fortified the primer with epoxy to give it impressive adhesion and seal against corrosion. The black-under-black also means fewer coats of Chassis Black paint are needed to achieve the final look.
Eastwood has bare chassis primer in one-quart cans for use with a paint gun or in 14-oz. aerosol spray cans. Both are formulated for use on undercarriage parts that are exposed to higher temperatures and stress than body panels. It’s a great choice on frames that have been stripped or media blasted, and you can also apply Chassis Black primer over existing finishes. Learn more about the Chassis Black system and our entire line of suspension paints by visiting the Eastwood Garage or calling the tech team at 1-800-343-9353. We’ll help you Do the Job Right on any restoration, repair job or custom build.
Eastwood Extreme Chassis Black Primer Features:
- Maximizes adhesion
- Improves chip resistance
- 14-oz. aerosol covers 8 sq. ft.; 1-qt. can covers 30 sq. ft.
- 2%-10% Gloss Level
Epoxy-fortified primer is the perfect foundation formulated specifically for Extreme Chassis Black® and Original Chassis Black.
| Product Name | Eastwood Extreme Chassis Black Primer |
|---|---|
| Warranty Term | 90 day |
| Is ESP | No |
| Is Canceled | No |
| 90 Day Returns | No |
| ATF Recommended products - Enabled | No |
| Storage Case Included | No |
| Do Not Use - Instructions - Depreciated | Aerosol 1. Read all directions and warnings for safe and proper application. 2. Clean all surfaces thoroughly to ensure surface is free from all grease, oil, and any polysilicons. Eastwood’s PRE is recommended. Make sure that steel is free from rust. For best results use when can and surface are between 70° and 90° F (21° and 32° C), 50% or less humidity. 3. If making spot repairs, feather-edge by sanding original finish with 220-320 grit. Do not use Extreme Chassis Black Primer over new enamel. 4. Shake can for 2 minutes after mixing ball moves freely. Use in a well ventilated area. 5. Apply by holding can 10 to 15 inches (25 to 30 cm) from surface. Spray two thin coats allowing 2 to 4 hours between coats. Opaque black color indicates full coverage has been achieved. 6. Can be top coated with Extreme or regular Chassis Black after 2 to 4 hours. 7. When finished, invert can and spray for 2 seconds to clean spray button. 8. Average coverage: 8 square feet. Quart 1. Clean all surfaces thoroughly to ensure surface isfree from all grease, oil, and any polysilicons. Eastwood PRE (#10041Z aerosol or #10194ZP quart) is recommended. Make sure that surface is free from rust. For best results use when can and surface are between 70° and 90° F(21° and 32° C), 50% or less humidity. 2. If making spot repairs, feather-edge by sanding original finish. Do not use Extreme Chassis Black Primer over new enamel. 3. Stir for at least 1 minute. Use in a well ventilated area. 4. Contents are thinned to sprayable consistency. If desired further thin with Toulol or Xylol. For Spray-on Application: Apply two thin coats allowing 2 to 4 hours between coats. Opaque black color indicates full coverage has been achieved. 5. Extreme Chassis Black Primer can be top coated with Eastwood Original or Extreme Chassis Black after 2 to 4 hours. 6. Finished article should be allowed to dry 48-72 hours before being handled. |
