Eastwood 4:1 Molten Red Metallic - Basecoat - Automotive Car Paint - Gallon
In stock
Eastwood Molten Red Metallic Basecoat Paint adds the superior durability of urethane to the ease of conventional basecoats.
- Apply a durable urethane finish wherever you live in the continental US, even CA
- Choose a fast, medium or slow Low-VOC Activator
- Makes 5 sprayable quarts
- Clearcoat is required on basecoat paints
- Mixes 4:1 with your activator choice
- Approximate coverage: 160 SQ FT
- Flake/Pearl Particle size: 10-60 microns
- Max Temperature: Paint will handle up to 300 degrees without delamination, but color shift may occur, so it should not be used in a high heat setting
- Made in the USA
- A scotching hot ruby red with a modern metallic effect
Basecoat Paint Kit is a low-VOC system, so it meets regulatory limits in highly-regulated areas, eliminating the need to switch to a waterborne system.
Product Name | Eastwood 4:1 Molten Red Metallic - Basecoat - Automotive Car Paint - Gallon |
---|---|
Warranty Term | 90 day |
Is ESP | No |
Is Canceled | No |
90 Day Returns | Yes |
ATF Recommended products - Enabled | No |
specifications_ax | BASECOAT PAINT MIXING RATIOSThoroughly mix four parts Low-VOC Urethane Basecoat with one part Low-VOC Urethane Activator. Use Fast (50308ZP) for small jobs, or temps below 75°F; Medium (50309ZP) for small jobs, or temps between 70-85°F; or Slow (50310ZP) for large jobs, or temps above 80°F. Keep in mind, other factors, such as humidity, air flow and total film thickness should also be considered. In many situations, it will be useful to add 10%-20% 50104ZP Zero-VOC Reducer to aid sprayabliity, flow and leveling. Remember, this is an activated basecoat system; only mix as much as is needed. Pot life is about 2 hours at 70°F. PAINT GUN SET-UP HVLP Gun: Fluid Tip 1.2-1.4 mm Inlet Spray Pressure 8-10 psi APPLICATION INSTRUCTIONSApply Low-VOC Urethane Basecoat color in two full medium wet coats with a consistent 50% overlap pattern. Allow five to ten minutes flash time between coats. Flash time should increase if additional coats are applied. Most colors will cover in two coats. A third and final coat may be applied to set even metallic pattern. If required, apply this light coat immediately after the previous full wet coat, moving the gun with faster passes, from further away. Mist basecoat onto the wet film until the metallic pattern is uniform. Basecoat should dry dust-free within 10-20 minutes. May be lightly sanded in as few as 20 minutes. Wait at least 30 minutes before wet sanding. Wait 45-90 minutes before taping on the fresh film. All dry times are approximate, at 70°. Temperature, air flow, total film thickness and other variable may extend these times. |
Storage Case Included | No |
Do Not Use - Application - Depreciated | Apply Low VOC Urethane Basecoat color in two full medium wet coats with a consistent 50% overlap pattern. Allow five to ten minutes flash time between coatts. Most colors will cover in two coats. A third and final coat may be applied to set even metallic pattern. Basecoat should dry dust free within 10 20 minutes. May be lightly sanded in as few as 20 minutes. Wait at least 30 minutes before wet sanding. Wait 45 90 minutes before taping on the fresh film. All dry times are approximate, at 70-Ý. |
Accessories | 15351 ZP 4:1 premium Clear Coat Kit, 51144ZP 2:1 European Clear Coat Kit, 14159ZP Urethane Reducer Quart, 14776 Concours PRO 2 Gun Kit, 20474 4 Stage air dryer system, 14842 Full face respirator, 12573ZP Surface clean and Prep Kit, 14743 18in x 738' Masking Paper |
Do Not Use - Instructions - Depreciated | |
Do Not Use - Safety Info - Depreciated | DO NOT USE THIS SYSTEM WITHOUT SUFFICIENT VENTILATION. Users must wear appropriate, properly fitted NIOSH approved activated charcoal cartridge respirator if a forced fresh air system is not available. Always wear eye and face protection, as well as gloves and protective clothing. Do not use this product, or be exposed to spray mist / vapors if you have respiratory problems. KEEP OUT OF REACH OF CHILDREN AND PETS. |