Eastwood 4:1 Pearl Neckless White - Basecoat - Automotive Car Paint - Gallon
In stock
SKU
16183ZP
Eastwood 4:1 Pearl Neckless White - Basecoat - Automotive Car Paint - Gallon is rated
out of
5 by
2.
With a gorgeous white pearl, this midcoat color has a subtle shimmer effect
Loading...
Eastwood Pearl Necklace White Basecoat Paint adds the superior durability of urethane to the ease of conventional basecoats.
- Apply a durable urethane finish wherever you live in the continental US, even CA
- Choose a fast, medium or slow Low-VOC Activator
- Makes 5 sprayable quarts
- Clearcoat is required on basecoat paints
- Mixes 4:1 with your activator choice
- Approximate coverage: 160 SQ FT
- Flake/Pearl Particle size: 10-60 microns
- Max Temperature: Paint will handle up to 300 degrees without delamination, but color shift may occur, so it should not be used in a high heat setting
- Made in the USA
- With a gorgeous white pearl, this midcoat color has a subtle shimmer effect
Basecoat Paint Kit is a low-VOC system, so it meets regulatory limits in highly-regulated areas, eliminating the need to switch to a waterborne system.
MUST BE APPLIED OVER PURE WHITE TO ACHIEVE PEARL.
| Product Name | Eastwood 4:1 Pearl Neckless White - Basecoat - Automotive Car Paint - Gallon |
|---|---|
| Warranty Term | 90 day |
| Is ESP | No |
| Is Canceled | No |
| 90 Day Returns | Yes |
| ATF Recommended products - Enabled | No |
| specifications_ax | MUST BE APPLIED OVER PURE WHITE TO ACHIEVE PEARL. BASECOAT PAINT MIXING RATIOS Thoroughly mix four parts Low-VOC Urethane Basecoat with one part Low-VOC Urethane Activator. Use Fast (50308ZP) for small jobs, or temps below 75°F; Medium (50309ZP) for small jobs, or temps between 70-85°F; or Slow (50310ZP) for large jobs, or temps above 80°F. Keep in mind, other factors, such as humidity, air flow and total film thickness should also be considered. In many situations, it will be useful to add 10%-20% 50104ZP Zero-VOC Reducer to aid sprayabliity, flow and leveling. Remember, this is an activated basecoat system; only mix as much as is needed. Pot life is about 2 hours at 70°F. PAINT GUN SET-UP HVLP Gun: Fluid Tip 1.2-1.4 mm Inlet Spray Pressure 8-10 psi Conventional Gravity: Fluid Tip 1.2-1.5 mm Inlet Spray Pressure 40-50 psi Conventional Siphon: Fluid Tip: 1.3-1.6 mm Inlet Spray Pressure 40-50 psi APPLICATION INSTRUCTIONS Apply Low-VOC Urethane Basecoat color in two full medium wet coats with a consistent 50% overlap pattern. Allow five to ten minutes flash time between coats. Flash time should increase if additional coats are applied. Most colors will cover in two coats. A third and final coat may be applied to set even metallic pattern. If required, apply this light coat immediately after the previous full wet coat, moving the gun with faster passes, from further away. Mist basecoat onto the wet film until the metallic pattern is uniform. Basecoat should dry dust-free within 10-20 minutes. May be lightly sanded in as few as 20 minutes. Wait at least 30 minutes before wet sanding. Wait 45-90 minutes before taping on the fresh film. All dry times are approximate, at 70°. Temperature, air flow, total film thickness and other variable may extend these times. |
| warranty_ax | 90 Day |
| Storage Case Included | No |
| Do Not Use - Instructions - Depreciated | |
| Do Not Use - Safety Info - Depreciated | Fully read and understans the instructions and warnings on the label of this product before use. Always wear proper safety equipment when using this type of product. OVC is 3.5lbs/gallon |
Related Products
