Eastwood 4:1 Pure White - Basecoat - Automotive Car Paint - Gallon
In stock
SKU
13567ZPA
Eastwood 4:1 Pure White - Basecoat - Automotive Car Paint - Gallon is rated
out of
5 by
2.
As white as white gets. Pure. Untinted. Absolutely white
Loading...
Eastwood Pure White Basecoat Paint adds the superior durability of urethane to the ease of conventional basecoats.
- Apply a durable urethane finish wherever you live in the continental US, even CA
- Choose a fast, medium or slow Low-VOC Activator
- Makes 5 sprayable quarts
- Clearcoat is required on basecoat paints
- Mixes 4:1 with your activator choice
- Approximate coverage: 160 SQ FT
- Max Temperature: Paint will handle up to 300 degrees without delamination, but color shift may occur, so it should not be used in a high heat setting
- Made in the USA
- As white as white gets. Pure. Untinted. Absolutely white
Basecoat Paint Kit is a low-VOC system, so it meets regulatory limits in highly-regulated areas, eliminating the need to switch to a waterborne system.
| Product Name | Eastwood 4:1 Pure White - Basecoat - Automotive Car Paint - Gallon |
|---|---|
| Warranty Term | 90 day |
| Is ESP | No |
| Is Canceled | No |
| 90 Day Returns | Yes |
| ATF Recommended products - Enabled | No |
| specifications_ax | BASECOAT PAINT MIXING RATIOS Thoroughly mix four parts Low-VOC Urethane Basecoat with one part Low-VOC Urethane Activator. Use Fast (50308ZP) for small jobs, or temps below 75°F; Medium (50309ZP) for small jobs, or temps between 70-85°F; or Slow (50310ZP) for large jobs, or temps above 80°F. Keep in mind, other factors, such as humidity, air flow and total film thickness should also be considered. In many situations, it will be useful to add 10%-20% 50104ZP Zero-VOC Reducer to aid sprayabliity, flow and leveling. Remember, this is an activated basecoat system; only mix as much as is needed. Pot life is about 2 hours at 70°F. PAINT GUN SET-UP HVLP Gun: Fluid Tip 1.2-1.4 mm Inlet Spray Pressure 8-10 psi Conventional Gravity: Fluid Tip 1.2-1.5 mm Inlet Spray Pressure 40-50 psi Conventional Siphon: Fluid Tip: 1.3-1.6 mm Inlet Spray Pressure 40-50 psi APPLICATION INSTRUCTIONS Apply Low-VOC Urethane Basecoat color in two full medium wet coats with a consistent 50% overlap pattern. Allow five to ten minutes flash time between coats. Flash time should increase if additional coats are applied. Most colors will cover in two coats. Basecoat should dry dust-free within 10-20 minutes. May be lightly sanded in as few as 20 minutes. Wait at least 30 minutes before wet sanding. Wait 45-90 minutes before taping on the fresh film. All dry times are approximate, at 70°. Temperature, air flow, total film thickness and other variable may extend these times. |
| warranty_ax | 90 Day |
| Storage Case Included | No |
| Do Not Use - Application - Depreciated | Prep surface and remove all traces of contaminants. Use Eastwood's PRE Prep. Sand existing finish with 400-600 grit abrasive. Reclean surface. Mix 4:1 with appropriate speed activator. Reduction not necessary. Shake Well. HVLP Gun Nozzle Size 1.2mm-1.4mm. Apply in 2 medium wet coats with 50% over lap. Allow 10 minutes flash time between each coat. Clear coat can be applied after 20-30 minutes. Maximum recoat time is 18 hours. Otherwise surface must be abraded with 400-600 grit. Use 50307ZP Low VOC Clear & Activator. Pot life is about 2 hours at 70-ÝF |
| Accessories | 51550 Concours HVLP Paint Gun 10194ZP PRE Painting Prep 20474 4-stage air drying system 50307ZP Low VOC Clear 50300ZP Low VOC Urethane Primer 11455/11456 respirator 51559 Digital regulator 51561Z Norton Liquid Ice Buff System |
| Do Not Use - Instructions - Depreciated | |
| Do Not Use - Safety Info - Depreciated | Always wear eye |
Related Products
